Category Archives: ESP12F

The Wall Display

ESP8266 Wall DisplayI’ve just spent time working on my hallway wall display, the amount of which would be considered commercial suicide. Good job it isn’t commercial.

Of course I’ve not just been working on the pretty colours – I’ve revamped the control codes for the ESP8266-driven controller twice, discovered and fixed an OTA flaw in the code, re-hashed the Node-Red driving code, found and fixed countless other bits and pieces… and in the process taken pause for thought as to why I ever used the Dark Skies Node… you know – in other words – pretty much revamped everything just to improve a simple display.

Continue reading The Wall Display

Facebooktwittergoogle_pluspinterestlinkedin

Simple Scope

SPIYou may have noticed that I’ve been working on my ESP8266 home control software (see the updates elsewhere along with new diagram), specifically upgrading and adding to the number of OLED and LCD displays I can handle, either by I2c or SPI.

I’ve been doing a lot of optimising and simplifying – for example with SPI – assuming that there will only be the one SPI device at once on an ESP means you don’t need the CS line which can be grounded.  But there’s more….

Continue reading Simple Scope

Facebooktwittergoogle_pluspinterestlinkedin

Icons

QD-TechIn case you were wondering – no, I’ve not gone off the boil, I’ve been quietly beavering away on my ESP8266 code since deciding to abandon the old ESP-01 and adding fonts for displays. Right now I’m focussing on the QD-Tech boards – 120x160 but I’ll eventually migrate the use of the various icons to the other displays now that I’m not terrified of running out of space.

Continue reading Icons

Facebooktwittergoogle_pluspinterestlinkedin

Grove LCD RGB Backlight

tmpD3E6Now, before anyone says anything – no I’m not advertising Seeed or their Grove stuff. It just so happens that over the weekend my pal brought some of their stuff over to have a play with and I was particularly taken by the LCD display. This is a typical Hitachi-style 16-character by 2 line LCD of the type that have been floating around since last century but which still are popular today I guess because of price. Anyway, this one marked “Grove-LCD RGB Backlight v1.0” is not particularly cheap but it has an RGB LED background and runs off I2c.

We tested it using the Seeed Studio WIO boards (more on that later). Lovely – want a pink background, or how about aqua, or mint -  well, you have full control over the RGB background with values 0-255 for each colour. It occurred to me that this really transforms the otherwise boring LCD display as you can use colour to indicate alerts etc.  For example on a thermostat display you could use orange for on, green for “reached set temperature” and blue for standby.

tmp52FBAnyway, as the WIO modules are little more than an ESP12 I thought it might be more useful to incorporate a driver for this display into my own ESP8266 code. Those of you familiar with the home control project will know that I keep updating the code for the Home Control 2016 project. So – I took a look at the Grove driver for this display – sadly it is in Arduino C++ format so I ended up doing quite a bit of changing to make it do what I wanted and in C – but ultimately it is in there and works a treat. Here are the new commands you can fire out in MQTT to the board with the new software on, using as usual GPIO4 and 5 for I2c.

{rgb_lcd_setup}

{rgb-lcd_clear}

{rgb_lcd_cursor:X,Y}

{rgb_lcd_background:RED,GREEN,BLUE}  // values 0-255 in each case

{rgb_lcd_write:”Your text”}

And that’s all there is to it. A nice addition to the code. I could add more if needed but I figured this minimal set of commands will do for most purposes.

I’m sure there will be other, compatible boards out there – if you know of them – do let us know.

So on the subject of the Seeed WIO boards, I’ve made a separate blog to follow on that – turns out that if you want to have a play, you can blow their code into an ESP-12 – but read the article coming soon.

Facebooktwittergoogle_pluspinterestlinkedin

VT100 Terminal for HC2016

rear view ESP8266 VT100Well, I had to give it a go, didn’t I – porting the code for the cheap VT100-type serial terminal into the main ESP8266 home control software.

BOY was that difficult but… after 2 days of head-scratching – check out the home control manual in the source code repository for Home Control 2016 – this  uses up four precious port bits (GPIO 13,14,15,16).

I have the terminal code up and running (minus baud rate controls… and the bottom line is now a general status line) and I have to say, fast doesn’t start to explain it.

As you can see in the image above, all we have here is the display with a slim ESP8266 board behind it – a WEMO D1 does the job superbly and you can use double sided tape to fasten the ESP8266 to the flat part of the board.  I just used a board I had handy The FTDI you see attached to the back is merely there to provide 5v power and, erm, stand the unit up!!!

At this point I’ll add what I seemed to have missed out of the original article – the pins!

Connections:  Connect VCC to 5v, ground to ground, light to 3v3.   GPIO16 to D/C, GPIO15 to CS, GPIO14 to SCK and GPIO13 to SDI (MOSI).  Connect RESET to RESET.  Leave the SDO (MISO) on the display unconnected.  The whole thing should light up.. and when you give the {ili_set:1} command and reboot the ESP, the display should clear and put up the header. That’s it.

ESP8266 VT100 front viewI did some tests to see if how fast I could make it -  I’ve already optimised the SPI and character routines – the board will not operate at all under ESP8266 at the fastest SPI speed so that is probably a dead-end, I tried caching the ROM reads (which are 8 bits – meaning you have to read 32 bits at a time and select the right 8 bits.

Caching that info actually very marginally slowed things down – I tried all sorts, writing 16 bits at a time to SPI – and finally after being able to obtain no more speed improvements, I stopped – not sure why I needed any of this as it was already blazingly fast.  Now, writing an X to every location on the screen (that’s 1600 character writes) takes 330ms so that is 200us per character (5*7). I think that is fast enough for now. Clear screen is near enough instant and scrolling is instant.

See this demo video of the ESP8266 version – the 328 version isn’t  quite THIS fast but it is still fast.

https://www.youtube.com/watch?v=YXqLVmoyKPE

So I’ve added some commands in the HC2016 project code

{ili_set:1}
The above will setup the display and make it available to accept data – once set the display will set itself up on power up of the unit.  Setting that command to 0 stops any data and from there on the display will NOT initialise on powerup.
{ili_text:"\e[35;40mHello there \e[32;40mmate\r\n"}
{ili_status:"All working exceedingly well"}
{ili_title:"\e[37;40mESP8266 Status Monitor"}

In addition to the above, {ili_rssi} puts the time and date down in the status area AND puts a nice phone-like RSSI indicator on the bottom right, showing the current WIFI signal strength of the ESP board. {ili_reset} resets the display after clearing it – to show the header and the LED rectangles on the top.

If you want to experiment with lines – and remember this is going via MQTT so don’t plan on making complex objects…  {ili_line:x1,y1,x2,x2,colour} but YOU WILL need to clear the screen first -  you can do that with  {ili_text:"\e[2J"} and when you’re done you can return the display to normal with {ili_reset}

{ili_pixel:x,y,colour} will draw a dot. {ili_rect:x1,y1,x2,y2,colour,background_colour} will draw a filled rectangle.
{ili_string:x1,y1,string} will position a string at an arbitrary location
{ili_fore:colour} will set the foreground colour for future strings
{ili_back:colour} will set the background colour for future strings

All of the above require that you clear the screen – you cannot do the scrolling terminal – and arbitrary text and lines at the same time but this does add a lot of flexibility (which I thought of much later than when I wrote this article originally).

The manual that comes with the bitbucket download is updated with new commands.

Hence by firing serial or MQTT commands at the board, I can get stuff onto the display.  To monitor all MQTT traffic was easy – over to the Pi and MQTT..

In Node-Red – a simple MQTT node picks up all traffic, passes it to a function – which then passes the result to the board which in this case is called “thisone”.

tmpPayload=”  “ + msg.payload;
tmpTopic="
\\e[36;40m"+msg.topic+"\\e[32;40m\r\n";
if (msg.topic!="thisone/toesp")
{
msg.topic="thisone/toesp";
msg.payload="{ili_text:\"" + tmpTopic + tmpPayload + "\r\n\"}";
return msg;
}

DisplayHence the board gets all traffic except for traffic destined for the board (which could end up in an infinite loop).

And now thanks to a conversation with reader Bob Green –  a WIFI signal strength (RSSI) indicator for the board and the time in the bottom left. I deliberately left the seconds out as this would typically not be refreshed that often – maybe every couple of seconds...

Bob suggested that by plugging the board into a battery pack you have a simple range tester and he’s absolutely right of course. Now, how to teach it to make coffee…

On the subject of terminals

No need to talk about VT100-type terminals for PCs – they’re coming out of our ears – but…

Android

I’d put this all together and I thought…an 80 line or 132 line version of this would be nice – I’ll put one on my Android phone. Well, you may well write in and tell me I’m wrong but I cannot find a VT-100 compatible serial modem for Android anywhere (I did find one but it was not clear if scrolling regions worked and it had a limited range of serial settings). Surprising considering that it can be done on a  relatively simple unit like the ESP8266

Linux

And that led me to Linux - or rather - I was thinking about the various single board computers I have lying around - a Pi would do but I have a rather nice FriendlyArm NanoPC T2 which was not quite fast enough for Android but runs a nice Debian.  I started looking for fancy graphical terminals - not a lot - nothing to anywhere near TOUCH some of the stuff on Windows - however I had this T3 with a little 7" LCD touch screen lying around and was determined it would not go to waste.

It turns out that the humble LX terminal does at least some VT 100 - but that pulls up a command line and lets you interact with it  -was there any way to get it to talk to serial instead - preferably one of it's own rather than a USB serial as it has FOUR serial ports on it.

Well, yes. I discovered this..

cu -l /dev/device -s baud-rate-speed

It looked as if this would let me use the terminal with serial instead of a keyboard- but of course when I tried it using:

cu -l /dev/ttyAMAT3-s 115200

I got zilch. The system didn't have a clue what CU is (neither did I for that matter).

Anyway, just for a laugh I tried SUDO APT-GET CU

And it worked. I tried again. THIS time all was well - but it could not contact the serial port - as it was "busy" - yeah right.

I added user FA (the user in control of that terminal session) to the relevant group - no difference - so as is often the case I just gave 777 permissions to the serial port and VOILA.

Terminal on Debian running serial

I tested some colour escape sequences from my PC Serial Terminal I wrote some time ago (and just recently updated to let me put ESC in there) and all worked well but for some visible representation of the ESCAPE sequences (which still worked). I continued experimenting and the UX terminal that comes with Debian LDXE does not suffer that particular issue – so it has the job!!!

Facebooktwittergoogle_pluspinterestlinkedin

HC 2016 Experiments

Throughout the development of the Home Control 2016 project I’ve constantly had the software tied a via a serial umbilical to my PC to monitor passing messages, make sure all is well etc. and to periodically check on RAM space to make sure nothing I’m doing is running away with precious memory.

You may have seen elsewhere that I’ve been working with a prototyping board which is basically an ESP12 with a prototyping area in which I’ve put rows of pins for ground, 3v3, 5v and the two lines I use for I2c as I add various peripherals culminating in the recent idea to use an Arduino 328 chip as an “ultimate peripheral”.

Well, we’ve taken that one a stage further and we’ve been discussing making our own prototyping board (Aidan’s a whizz at PCBs and of course we use the likes of Dirty PCBs in China so it is quite cheap to knock up a few boards) and the last few days I’ve been formulating a planas Aidan puts together the schematic. What I’ve realised is that I always run out of the power and ground lines no matter what I do. Add to that the FTDI so I can monitor serial Comms and it all gets a bit messy.

Display for HC2016

So right now we’ve been discussing a board with the ESP-12 module with lots of pins and additionally a 328 SMT chip with Xtal. Of course that means 2 serial monitors. I’ve been playing with the old QDTech 128*160 displays since I discovered that they work pretty well when driven from the proper SPI pins on Arduinos (don’t even think of using software SPI on them) and ramping up the SPI speed – and so it was that in conversation, we were saying “if only you could scroll them” – that led to thoughts of having a RAM buffer larger than the total available on the ESP8266 or Arduino and… well, I thought I’d use our friend Google to go take a look. It turns out – I was completely unaware of this and VERY pleasantly surprised to find – that the QDTECH chip has the ability to scroll up built in – all that is needed is to scroll up an area then paint a fast horizontal black line after each scroll. 

There is a version of the driver for the board here and at some point in 2014, it turns out that an M J Sage added this scrolling ability. Well done.  I wonder if he or she realised what a useful addition this could be.

So now we have a display, easily driven by the 328 which can scroll constantly (I’ve had it on several night’s test) and hence provide a boatload of status info. Top and bottom can if needed remain static.

First Stab

We’re going to incorporate the display onto the prototyping board and it won’t take any additional space as it will sit neatly over the other components! The image above probably bears no relation to the final board but I’m just trying to convey an idea here. The prototyping area on the right of the board will be chock-full of PTH holes but there will be long runs of connected holes for power and I2c as these end up being needed the most with connector wires. All 0.1” of course.

With the QDTech display you can connect the reset line to the 328 reset and hence here are my first thoughts at the use of the 328 which will have access to A6 and A7. I’ve pretty much got this working – just need to add in the temperature handling code I already have for Dallas and DHT chips.

D0-7 – general purpose port extender – inputs or outputs or any mix
D8     D/C for QDTECH
D9     16- BIT PWM out
D10  16-BIT PWM out
D11   MOSI for QDTECH
D12   MISO
D13   SCLK for QDTECH
A0      CS for QDTECH
A1      Temperature
A2      Temperature
A3       Debounced input
A4      I2C to ESP
A5      I2C to ESP
A6      Analog in 1
A7      Analog in 2

Aside from losing GPIO2 and GPIO14 inputs (as they’ll run the I2c) the ESP use will remain the same.  The only restriction being that we cannot run ESP PWM at the same time as the I2c due to timing interference– a pain but not something I can see away around. The I2c 16-channel PWM controller does seem a good way around this as it offloads all PWM work onto a cheap board – for single colour PWM lighting the new 16-bit PWM on the 328 works fabulously.

Given that the 328 can handle inputs for the main board we can do away with our normal GPIO2 and GPIO14 and they can have the job of I2c, leaving all normal outputs as for the existing system.

I guess the end-game here will be the smallest possible board that contains both the 328 and the ESP wired to this spec for general use. But that comes later after we see how well all of this works in practice. First the prototyping board. Watch this space.

Sadly in the link I’ve enclosed, the author refers to Banggood who used indeed to offer these displays for under £3 at a time when there were no software drivers for them – (I think we paid £2.60) but I’ve noticed recently that Banggood have been getting greedy and jacking their prices up – a cursory check of the link shows they now want £5.48 for these simple LCD displays – well good luck with that Banggood.

The only ones I’ve found up to now – and the price is good – as usual – is AliExpress.

Someone have another link?  the board has an 8-way connector at one end and a larger connector at the other – with a full size SD socket on the underside. See the AliExpress link.

This blog entry could well change dramatically as we spot fatal flaws in the plan above Smile

Facebooktwittergoogle_pluspinterestlinkedin

Faster ESP I2C

Experimenting with I2c on the ESP8266? I am – and I’m having a great time with it. If you’re using my code you don’t really need to think about it but if you’re hunting around for better I2c for the ESP – or maybe interfacing the ESP8266 to Arduino – then you’ll love the stuff I’m doing right now – and yes, I AM looking for I2c experts to tell me if I’m doing something wrong because it is all going rather too smoothly.

I decided to take the end from the info from the last blog entry and separate it off as I learn more about I2c (which to recall is a simple 2-wire multi-drop serial communication protocol with separate clock and data).

Why read this? Well, up to now because I spotted a howling issue in the WIRE library for Arduino, found an improvement on the ESP8266 SDK I2C code in the ESPRUINO changes to the Espressif I2c code - I think I found a mistake in it, fixed it then SAILED past the original speeds, reducing a 15ms package best case to well under 3ms  while adding clock stretching into the bargain.  I should clarify at this point that I am NOT an expert in I2C but hey – I can’t get this to fail so I might be onto something! Read on!

So firstly let’s recall -  I’ve been trying to make an Arduino peripheral for the ESP8266 Home Control 2016 project.  I started with the WIRE library in Arduino, working on a small NANO device. I discovered that there are two buffers in WIRE that are 32 bytes in length and hence limit packages to less than that  - I replaced them with a couple of 128 byte buffers and solved lots of issues I’d been having – that is detailed in the last blog.

Where we left off, I’d made a test setup to send a message to the newly-created NANO peripheral which right now on my bench handles a QTECH display and some IO. The ESP8266 I2C is also talking to a BME280 temperature/pressure/humidity sensor and a PWM expander board – so there are 3 devices – some input, some output.

In the last blog entry I’d added a test command for the ESP which could be sent to the board serially or by MQTT and went like this…

{nano:9,7,"how are you today and the weather is nice - NO REALLY it certainly is.",0}

Simple enough – send a message to device 9 (my chosen default address for the NANO peripheral), command 7, a string – and a dummy 0 on the end to tell the device not to bother sending any return info.

As you can see below, this operation takes, using the standard Espressif Ic2 Master code, 15ms in total – not stunningly fast but ok.i2c_thumb2

Flush with the success of finding that buffer issue, I decided to go into the ESP I2C library and have a tinker – changing all the delays into ‘'#defines so I could mess with them. So without any real effort I could reduce delays from 14ms to 6ms – a very worthwhile improvement. bear in mind however that the ESP code has no clock-stretching and hence no way for the peripheral to slow things down. I am told that the call-back routine within WIRE holds the clock down until it is finished, in order to slow things down – this would do nothing but cause havoc for the Espressif code.

Below is a read operation which I got to work properly after reading  this video – as I had no idea what a re-start was – see the little green circle just after the third byte.

read_thumb2

As you can see in the image above I address device 9 (18 as it is shifted left by one – i.e. 7 bit addresses but the bottom bit is reserved to indicate a read or write) – I fire command 2 to read port 4 – then with an I2s restart (start without a preceding stop), I  resend to the device with the LSB set (ie 19) and get a value 0 back (from a pin)  All in a matter of a millisecond.

I was at this point getting worried about lack of clock-stretching – in which a slave can hold the clock low to “stretch” things out a bit – about the only control the slave has!

It looked as if this forum might have some answers as their modification of the ESPRESSIF code certainly had clock stretching in it. It involved some changes and I decided to pick the best bits from their modification.

So they’ve simplified the code a little – while adding in clock-stretching – by replacing a simple delay with a check for clock low – easy enough when you look at it… but they also seemed to have completely messed up master_start – at least, they had it the opposite way to Espressif – and accordingly, repeated starts – as I use in getting data out of a Nano above – simply failed. The logic probe said this was all wrong.

So I reversed master_start back to the way Espressif have it  –so I ended up with a mix of the old and new – and the result – well, up to now everything works – and that long 15ms string send was now reduced to under 5ms from 15ms.

5ms string_thumb[2]

I tested the code with the PWM chip I’ve been playing with and the BME280 – so that is both reading and writing and up to now both were working perfectly. 

It was notable that the clock low period was now much longer than the clock high period and I wondered if there is any way to shorten that.  You know when you get deeply into code and all of a sudden it all becomes clear.  I realised that setting and checking ACK signals was a function – with all that entails – I changed that to a macro. I realised that delays in loops were really un-necessary as the loop itself would cause delays.. I took them out.

At this point I had backed everything up expecting my experiments to fail miserably. I tested the new code and everything worked. I got the logic probe out again.

3ms

My original test string at 15ms was now down to 3ms and according to the probe – all is well. I DID get it down to 2.5ms but the probe said I was doing restarts in the middle of the string – I’ll find another way around that one. Current state of the art – 2.9ms

As for reads – my original byte read was taking somewhat over 1ms – it now takes 0.25ms.

fastish read

And of course I’ve concentrated on the read and write routines leaving the inter-byte handshaking pretty much along so maybe there’s another 10% improvement to make here without dipping into ESP assembly language.

https://bitbucket.org/scargill/esp-mqtt-dev/src 

The driver and firmware libraries in the repository above contain the modified Espressif i2c_master code – and also other I2c wrappers for sending packages – they are fine – any further optimisation needs a good solid look at the one file (and it’s header) for i2c_master.   Open to ideas (that don’t involve converting Arduino assembly language to work with the ESP SDK – been there, failed).

I have just noticed that in the write cycles, there is still more off-time than on for the clock – and so I just took a delay out – which SHOULD mean the off-time is way too slow but because of the time taken to call and process the function – we still end up with 0.9us on time and 1.3us off time – everything continues to work on the tests I have – yet the total time for that read drops from 0.25ms to 0.21ms and the string write time from 2.9ms to about 2.2ms – again – worthwhile improvements.

That simple change was made in the write routine…

void ICACHE_FLASH_ATTR
i2c_master_writeByte(uint8 wrdata)
{
    uint8 dat;
    sint8 i;

    for (i = 7; i >= 0; i--) {
        dat = wrdata >> i;
        I2C_MASTER_SET_DC(dat,0);
      //  i2c_master_wait(I2C_DELAY_5);
        I2C_MASTER_SET_DC(dat,1);
        while (!GPIO_INPUT_GET(GPIO_ID_PIN(I2C_MASTER_SCL_GPIO))) {}
       I2C_MASTER_SET_DC(dat,0);
    }
}

Logic analyser says yes, 3 test items say yes… how low can it go!

Facebooktwittergoogle_pluspinterestlinkedin

I2C the Easy Way

I2c on IOTBEARIf you’re going to experiment with I2C – may as well do it the easy way. Having spent the past few days with a desk that looks remarkably like a bowl of spaghetti, I’ve finally gotten around to making a special IOTBEAR board up for the job. 18 each of ground, +3v3 and +5v lines – and 16 each of GPIO4 and GPIO5.

This gave me the opportunity to tackle that long string problem in Arduino Wire. A brief attempt with the logic analyser suggested that my ESP i2c was sending out at least one byte more than the Arduino was receiving – impossible to tell if more because the ESP would stop sending as soon as the Arduino would stop receiving.

And that brings me to a question – is anyone aware of a nice, pretty I2c and other protocol analyser based on a Raspberry Pi? Seems to me that would be a good use for an old RPI2?

Anyway I digress… I’ve had issues with I2c experiments in the past – usually when sending strings. I’ve looked up the issue on Google and found nothing. I was convinced it was a timing issue and at that point I Skyped my friend Peter Oakes in Canada – just as with Aidan who you’ll have read about in here, I often find that “two heads are better than one” when I’m getting bogged down.

We started sending I2c strings to the Arduino who’s receive buffer I’d put a Serial.println() statement in – to see how many characters it THOUGHT it was receiving.

29…. 30… 31… 32… 32   - EH

As I increased the length of string sent from the ESP (using ESP software I2c) to the Arduino (using the WIRE library) at 33 characters the Arduino thought it was getting 32 – at 34 it went to meet it’s maker.

VOILA – the WIRE library clearly has a buffer to store stuff – I did not believe at first that 1. the buffer would be so small and 2. this would result in a crude crash.  I went into the Wire Library (that’s a long story – I have dozens of WIRE libraries and it took a while to find the right one) – updated the buffer size in wire.h and… nothing – made no difference. I introduced an error into the .h file to make sure I had the right one – sure enough  - but no joy on fixing the problem.

I don’t know if Peter or I twigged first but in my ESP SERIAL buffering which I wrote myself, I have a 256 buffer for incoming characters – which fills until it gets a CRLF then transfers that to an output buffer of the same size – so that incoming characters can continue to arrive while processing the buffer. It occurred to us that maybe the Wire library has the same setup – SURE ENOUGH. Not only is there a buffer definition in arduino/hardware/arduino/avr/libraries/wire/src/wire.h but also in arduino/hardware/arduino/avr/libraries/wire/src/utility/twi.h

And yes, the directory structure IS that complicated (I’m on Arduino 1.69) – sure enough two separate 32 byte buffers are created.  As I have never seen this covered so I assume I’m the only person in the world who’s ever sent 32 bytes via I2c… but if you’re about to try the same – and you’ll need to if you want to try my peripheral software, then I suggest despite the deep hole this will leave in RAM (all 2K of it) – making both of these 128 bytes.

Since amending and re-compiling – I can now send long strings to the Arduino absolutely to my heart’s content!

{nano:9,7,"how are you today and the weather is nice - NO REALLY it certainly is.",0}

Around 15ms in total – not stunningly fast but fast enough not to interfere with the running of anything.

For more on I2C – see the blog entry “Faster ESP I2C”

Facebooktwittergoogle_pluspinterestlinkedin

Arduino Peripheral for HC2016

As many of you know, I don’t have a great deal of time for Arduino – I cannot tell you how many months I wasted on those daft cheap Ethernet boards for them which never really worked reliably no matter what I did – so I probably have a mental block by now.

However, there can be no arguing that a board costing £1.28 inc. postage has to be worth at least a second look. The picture below shows where this all fits into the scheme of things…

Home Control 2016

And so it was today, I’d just finished putting some polishing touches on the I2c code, fresh from having gotten the BMP280 working – and I was looking at A/D boards to add to the arsenal when I remembered that Arduinos have A/D in… not stunningly high definition but good enough for checking batteries and light levels etc.

Nano[6]At that point, mid-coffee I remembered I’d bought one of these little critters from AliExpress. Be careful – not all of these bring A4 and A5 out, some have micro-usb connectors, others don’t. Some have 3v3 regulators, some don’t.  I find the most useful ones just have the FTDI connector on them and no USB – but then I have FTDI connectors coming out of my ears.

For the purposes of this item – a 3v3 regulator is not needed as presumably if you’re fastening I2c devices to the ESP8266, you’ll feed 3v3 to the whole lot. Anyway, use whichever suits you best. I’m also assuming pullups are in place – the Arduino has pullups but I doubt they are strong enough.

SO – the point of this is – it is quite easy to make an Arduino into an I2c slave – so for £1.28 you can make a port extender, more inputs, some analog inputs, PWM outputs – just about anything really as long as whatever it is doing doesn’t take up any time as the board needs to respond to I2c commands quickly. I have a MUCH more powerful device on the way from China with lots more pins etc. but for now, the humble Chinese Nano gets the job.

The simple WIRE library with a little code turns the Nano or similar into a device – I’ve chosen to make it DEVICE 9 by default  – don’t REALLY want to use up ports making that programmable but then because the board has EEPROM I’ve made a hopefully reliable method to store the device number in EEPROM!

In the simplest example, sending I2c commands to this device from the home control software discussed elsewhere in this blog – let’s say to turn output 13 on…

{nano:9,1,13,1}

And indeed that was the very first command I made it respond to as an I2c slave – mainly because on these boards, port 13 has a LED attached to it!!!

Clearly turning it off would be:

{nano:9,1,13,0}

Or how about reading the state of input 10?

{nano:9,2,10}

So here I’ve chosen to create the command nano – command 1 is set ports (2 is read ports)… port is 13, last parameter is 1 or 0 for on or off.  Immediately we have a port expander with several useful ports. For ease, the software I put into the Nano checks to see if the port has already been setup correctly and does that if not – hence avoiding annoying setup code at the ESP end.

With the simplest code and assuming A4 is used as the SCL and A5 is used as SDA, you end up with a “nano i2c peripheral” able to offer (if you get the right board offering A0-A7):

  • 6 8-bit PWM channels
  • 6 8-bit ANALOG inputs
  • 6 DIGITAL INPUTS or OUTPUTS

i.e. ALL of that. You could instead choose to have 18 general purpose I/O lines etc.

I’m sure it would not take most of you too long to figure out ALL SORTS of other configurations but for the sake of this project and this board example– there are ports 2-21 where Arduino A0 is 14. Now,  if your board DOES have A6 and A7, note that they can ONLY be used as analog inputs – they cannot be used as ordinary inputs OR outputs – that’s just a simple feature of the board, not the software.

The point being – they are SO cheap and with this code make good general purpose I2c peripherals – you have to ask yourself – in some cases, why you would use anything else!

So before we start – this will only work for short strings or series of numbers with the standard WIRE library for Arduino – see the blog where I learned the hard way this weekend that WIRE has a 32 byte incoming buffer AND a 32 byte transfer buffer and if you try to send more than that – the Arduino crashes – I’ve updated my WIRE to 128 bytes (so that’s 192 bytes more than before ) and it is working a treat with long strings – the reason I want that is because though you won’t see it in this basic code, I’m now working on running QTECH 160*120 displays in the Arduino peripheral.

I’ve updated the code and here is the current state of affairs – evolving rapidly, for the Nano - expect this to change – again  -  this time tomorrow it will no doubt have changed - again.

 

//
// A simple i2c SLAVE - default device number 9 - reads instructions from
// master and either sets outputs or returns inputs accordingly.
//
// 
#include <Wire.h>
#include <EEPROM.h>

#define MAXPORTS 21
#define ADDR_LOC1 0
#define ADDR_LOC2 1

#define SET_OUTPUT  1
#define READ_INPUT  2
#define READ_INPUT_PULLUP 3
#define SET_PWM     4
#define READ_ANALOG 5
#define SET_ADDRESS 6

byte ports[MAXPORTS];
byte params[6];
byte paramp;
byte retParam;
byte bigcount;
byte device=9;

void setup() {

  byte eeprom1,eeprom2;
  eeprom1=EEPROM.read(ADDR_LOC1); eeprom2=EEPROM.read(ADDR_LOC2); 
  if ((eeprom1^eeprom2)==255) device=eeprom1; // programmable address
  bigcount=0;
  Wire.begin(device);           // join i2c bus with address #9 by default
  Wire.onReceive(receiveEvent);
  Wire.onRequest(requestEvent); 
  for (int a=0;a<MAXPORTS;a++) ports[a]=0;
  paramp=0;
  retParam=0;
}

void loop() {}  // not used yet

// function that executes whenever data is requested by master
// this function is registered as an event, see setup()
void requestEvent() {

  Wire.write(retParam); // respond with message of 1 bytes as expected by master
  //Wire.write(34); // respond with message of 1 bytes as expected by master
  //Wire.write(45); // test
  //Wire.write("This is it you know",19);
}

// function that executes whenever data is requested by master
// this function is registered as an event, see setup()
void receiveEvent(int count) {
int tcount;
tcount=count;
paramp=0;
// no time consuming in here or the routine to send a byte back will be missed.
  while ((tcount--)&&(paramp<128))
   {
    params[paramp++]=Wire.read(); 
   }
  switch (params[0])
    {
    case SET_OUTPUT:
          if (ports[params[1]]!=1) { ports[params[1]]=1; pinMode(params[1],OUTPUT); } 
          digitalWrite(params[1],params[2]? HIGH : LOW); params[0]=0;
          break;
    case READ_INPUT:
          if (ports[params[1]]!=2) { ports[params[1]]=2; pinMode(params[1],INPUT); } 
          retParam=digitalRead(params[1]); params[0]=0;
          break;
    case READ_INPUT_PULLUP:
          if (ports[params[1]]!=3) { ports[params[1]]=3; pinMode(params[1],INPUT_PULLUP); } 
          retParam=digitalRead(params[1]); params[0]=0;
          break;          
    case SET_PWM:
          if (ports[params[1]]!=4) { ports[params[1]]=4; pinMode(params[1],OUTPUT); } 
          analogWrite(params[1],params[2]); params[0]=0;
          break;
    case READ_ANALOG:
          if (ports[params[1]]!=2) { ports[params[1]]=2; pinMode(params[1],INPUT); } 
          retParam=analogRead(params[1]); params[0]=0;
          break;    
    case SET_ADDRESS:
          EEPROM.update(ADDR_LOC1,params[1]); EEPROM.update(ADDR_LOC2,params[1]^255); 
          // update address - will take effect on next powerup of the device as you 
          // can only call "begin" once
          break;      
    default: break;  
    }
}

Facebooktwittergoogle_pluspinterestlinkedin

BMP280 for HC 2016

I have just added a working BMP280 implementation into the Home Control 2016 code (see right menu in blog) returning temperature and pressure.  Add that to the (already implemented) BME280 code, Seeed display, 16,channel PWM, port expansion and more, it’s not been a bad development week really! Manual updated.

The BMP280 as you know does not have humidity – but is cheaper than the BME280.The manual is updated and has details on addresses etc.  Just waiting now for the A/D board to turn up from China.  I’m quite getting into this i2c expansion.

This little picture attempts to show the current state of play for Home Control 2016. No doubt I’ve missed loads off but as you’ll see quite a bit has been added recently.

Home Control 2016

Facebooktwittergoogle_pluspinterestlinkedin